S355JR structural steel plate is a high-strength low-alloy European standard structural steel covering four of the six "Parts" within the EN 10025 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry and physical properties similar to ASTM A572 / 709.
EN10025 S235JR steel plate standard and specificationThickness:5 200 mm. Width:Up to 3.5 metres wide. Length:Up to 14 metres long. Certification:EN10204 3.1/3.2. Steel Number:1.0038. Delivery Condition:As Rolled or Normalised. Comparison of Steel Grades. S235JR DIN EN 10025-2 Number:1.0037. EN10025:1990.
Our range of S355JR+N High Tensile EN 10025 Coils is a cost-effective way of flanging in low pressure. S355JR+N High Tensile EN 10025 Sheets is as well obtainable in different shape and size according to the need of our well-regarded patrons. S355JR+N High Tensile EN 10025 Plates are mass-produced according to applicable international standards.
S355 Structural Steel Plate, S355JR Structural Steel Plate S355 Steel Plate, S355JR Plates, IS 2062 E350 A Structural Steel Sheets Exporter, SAILMA 350HI High tensile Structural Steel Plates Stockist in Mumbai, India. Conquest Steel & Alloys is an exporter of S355 Structural Steel Plates , known for massive strength and competence in hostile conditions.
S355J2+N steel plate,S355J2+N steel plate specification S355J2+N steel plate under EN 10025 standard, S355J2+N steel plate is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel.With its low carbon equivalent, it possesses good cold-forming properties. S355J2+N steel plate is produced by fully killed steel process and supplied in n normalized or controlled rolling condition.
Among the chemical elements of S355JR steel, the maximum percentage of each element is as below:Carbon content (C) is 0.27 percent. Manganese content (Mn) is
S355JR datasheet, S355JR property, S355JR - Steel gradesStainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S355JR can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86-816- FAX:+86-816-2 M/B:+86-15386639257 E-mail:[email protected]
S355JR steel plate|S355JR+N|S355JR+AR plate--Xin Steel S355JR--A structural grade (S) with at minimum yield strength of 355 N/mm²m, the JR designation confirms that the steel has undergone longitudinal Chary V-Notch impact testing at 27J (Joules) at room temperature. S355JR+N--A structural grade (S) with the same minimum yield strength of 355 N/mm²m, but supplied in an 'Normalized condition'.
Steel Coil Specifications Coil specifications table refers to Base Metal Thickness (BMT). (example:. BMT + Z coating (.mm) = approx. .mm Material = Zincalume, Galvalume or G-/ gms/m î galvanised steel Coil must be un-oiled (dry) type Decoiler coil weight recommended not to exceed kgs, unless larger decoiler stamped with ,kg High tensile steel
Structural Steel - EN10025 S275, S355JR and S355JOS355 being widely used in the structural engineering and construction industries, S355 offers high yield and tensile strength and is supplied with a variety of treatments and test options to ensure that it is a highly usable steel in your various projects. S355 structural grade (S) carries minimum yield strength of 355 N/mm²m, the JR designation confirms that the steel has undergone longitudinal Chary V-Notch
Structural Steel Plate and Strip to EN 10025Coil from 1,6mm - 13mm. (Vanderbijlpark) Coil from 1,5mm - 6mm. (Saldanha) Other thicknesses may be available on enquiry In addition, structural steel plate and strip to American, other European and Japanese specifications are available on enquiry. Refer to Table 4 for a list of the corresponding former national designations.
5mm steel checker plate s235jr s235j0 s235j2 s275jr s275j0 s275j2 s355jr s355j0 s355j2 s355k2 hot Rolled chequered plate with tear drop pattern, checkered plate 6mm 10mm detail information Thickness 1.0-200mm Width 1250mm,1500mm,1800mm,2000mm. ,2500mm or as required Length 2000-12000mm Standard AISI, ASTM, BS, DIN, GB, JIS Material A36,SS400,SPCC,SPHC, Q195, Q 235,Q345
steel s355jr price, steel s355jr price Suppliers and A wide variety of steel s355jr price options are available to you, such as aisi, astm, and jis. You can also choose from bending, cutting, and punching steel s355jr price, as well as from container plate, flange plate, and boiler plate steel s355jr price, and whether steel s355jr price is ce.Steel S355JR:characteristics, properties, analogues Steel s355jr characteristics. Steel grade S355JR is used to manufacture hot-rolled flat and long products, which are subsequently used when producing steel building structures. Classification:Non-alloy structural steel. Products:Flat and long products, semi-finished products.